Product classification
PTFE
-
White PTFE Coated Fiberglass Fabric High Temperature Expanded
Expanded PTFE Teflon sealing tape(Teflon Sealant Joint Tape) is made with un-sintered PTFE/Teflon. PTFE is resistant to all chemical products and solvents with the exception of alkaline materials. It has good resistance to elevated pressures and has a high thermal stability. Expanded PTFE sealing tape is odourless and tasteless making it suitable for food applications and is WRC approved for use with potable water. Expanded PTFE Teflon sealing tape is a kind of dynamic sea. It has extremely low coefficient of friction, non abrasion, excellent seal ability, does not hydrolyze and so on
-
Skived High Temperature Fiberglass Tape Bronze Filled Teflon
Skived PTFE Teflon tape commonly known as teflon film or PTFE film - is manufactured by technics of compacting, sintering, rotary cutting with PTFE granular resin. As PTFE has a very low co-efficient of friction, so the surface of skived teflon PTFE film has similar friction levels to ice. Skived teflon PTFE film can work at -180°C ～+260°C and is the best electrical insulator of all known plastics. Skived PTFE Teflon tape can be used as lining, seal components, wire isolation, slide block, gasket, seal, dielectric material and so on.
-
Light Weight PTFE Teflon Sheet , Non-Flammable Black PTFE Slide Bearing
PTFE Teflon slide bearing commonly known as teflon bearing or PTFE bearing - is manufactured by technics of molding, sintering and finalizing the design to various sizes with PTFE suspension resin. It can be adhered to rubber and metal with one side etched. And different fillings can be used to achieve special demands. PTFE slide bearing can work at -180°C ～+260°C and is the best electrical insulator of all known plastics. PTFE bearing slide is made from high strength PTFE suspension resin by methods of moulding, sintering and finalizing the design to various sizes. Different fillings can be used to achieve special demands. It can also be adhered to rubber and metal with one side etched.
-
Extruded PTFE Teflon Rod / Pure White PTFE Rod For Mechanical, High Temperature Resistance
Extruded PTFE Teflon rod is manufactured by technics of paste extruding and ram extruding method in the diameter from 5 to 300mm with PTFE granular resin. As PTFE has a very low co-efficient of friction, so the surface of extruded teflon PTFE rod has similar friction levels to ice. Extruded teflon PTFE rod can work at -180°C ～+260°C and is the best electrical insulator of all known plastics. Extruded PTFE Rod is available in both virgin grades and reprocessed (mechanical) for less demanding applications.
-
Extruded PTFE Rod / Teflon Rod For Sealing , High Chemical Resistance
Extruded PTFE Teflon rod is manufactured by technics of paste extruding and ram extruding method in the diameter from 5 to 300mm with PTFE granular resin. As PTFE has a very low co-efficient of friction, so the surface of extruded teflon PTFE rod has similar friction levels to ice. Extruded teflon PTFE rod can work at -180°C ～+260°C and is the best electrical insulator of all known plastics. Extruded PTFE Rod is available in both virgin grades and reprocessed (mechanical) for less demanding applications.
-
Molded PTFE Teflon Rod , 3000mm Length PTFE Rod / Teflon Rods For Chemical
Molded PTFE Teflon rod is manufactured by technics of extruding and molding method in the diameter from 10 to 500mm with PTFE granular resin. As PTFE has a very low co-efficient of friction, so the surface of molded teflon PTFE rod has similar friction levels to ice. Molded teflon PTFE rod can work at -180°C ～+260°C and is the best electrical insulator of all known plastics. Molded Teflon rod and cylinders for machining in a wide range of sizes. The most common sizes are listed in the table below, but many other combinations of OD and ID are available. Molded rods are preferred for machining because compression molding yields greater material homogeneity for the finished part.
-
100mm Width Black Teflon Rods / PTFE Rod For Chemical , Self Lubricating
Filled PTFE Teflon rod is manufactured by technics of molding method in the diameter from 5mmto 500mm with PTFE granular resin. As PTFE has a very low co-efficient of friction, so the surface of filled teflon PTFE rod has similar friction levels to ice. Extrusion teflon PTFE rod can work at -180°C ～+260°C and is the best electrical insulator of all known plastics. Filled PTFE Teflon rod has strong corrosion resistance and friction-resistance,By adding filler such as glass fiber,carbon fiber,copper powder,graphite,asbestos,MOS2,AL2O3,carbon powder,ceramic fiber, metal powder,polyamide,PS,the hardness,compression strength and abrasion resistance of the products is improved ,in addition,it will have good heat conductivity and low heat expansion coefficient.
-
500mm Black Filled PTFE Teflon Rod / PTFE Rod / Teflon Rod For Sealing
Filled PTFE Teflon rod is manufactured by technics of molding method in the diameter from 5mmto 500mm with PTFE granular resin. As PTFE has a very low co-efficient of friction, so the surface of filled teflon PTFE rod has similar friction levels to ice. Extrusion teflon PTFE rod can work at -180°C ～+260°C and is the best electrical insulator of all known plastics. Filled PTFE Teflon rod has strong corrosion resistance and friction-resistance,By adding filler such as glass fiber,carbon fiber,copper powder,graphite,asbestos,MOS2,AL2O3,carbon powder,ceramic fiber, metal powder,polyamide,PS,the hardness,compression strength and abrasion resistance of the products is improved ,in addition,it will have good heat conductivity and low heat expansion coefficient.
-
3000mm Length PTFE Rod / Teflon Rods For Electrical Insulation , High Temperature Resistance
Extruded PTFE Teflon rod is manufactured by technics of paste extruding and ram extruding method in the diameter from 5 to 300mm with PTFE granular resin. As PTFE has a very low co-efficient of friction, so the surface of extruded teflon PTFE rod has similar friction levels to ice. Extruded teflon PTFE rod can work at -180°C ～+260°C and is the best electrical insulator of all known plastics. Extruded PTFE Rod is available in both virgin grades and reprocessed (mechanical) for less demanding applications.
-
Pure White PTFE Teflon Rod / PTFE Teflon Square Bar For Electrical Insulation , Long Durability
PTFE Teflon Square Bar is a low friction fluorometry with outstanding chemical and weathering resistance. The working temp range is -20° F to 500° F. It has the lowest coefficient of any solid. It has no slip-stick characteristics; static and dynamic coefficients are equal. Nothing sticks with any strength to unheated surfaces. Both virgin and mechanical grades are UV stabilized. PTFE Teflon Square Bar easily fits into compatible grooves, slots, and ways without additional machining. Smaller sizes will bend (within limits) to conform to bends in the fitting groove or slot. Made of unfilled virgin PTFE square bar is inert, frictionless, and non-reactive and works in applications from -350F to +500F. Different lengths are available on special order